Plumbing for Beginners: What You Need for Bathtub Installation
Plumbing for Beginners: What You Need for Bathtub Installation
Blog Article
We have stumbled on this post about How to Install a Bathtub Yourself down the page on the net and think it made good sense to relate it with you in this article.
Setting up a bath tub isn't exactly rocket science, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a new one is likewise a moderately tough task. If the old bathtub is conveniently obtainable, the project can move quickly; if you have to open a wall to get rid of the old bathtub as well as position the new bathtub, the job is much harder. In either situation, the project is within a home handyman's abilities, although you will need an assistant to leave the old tub and also embeded in the new one. See to it you have certified yourself for the task as well as fit trying it. Instead of working with a service provider to take control of a halfway-completed task, it is much better to consider using one before you begin. Chances are you might require a professional plumber to make tube connections.
This post will aid you install a new bathtub in your washroom if you have already purchased a new tub and don't need to change the setup of your previous water pipes.
Your tools and also material list must comprise the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather bothersome as a result of the restricted gain access to that is usually the case.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a fabric prepared for the staying water that will come from the pipes. As soon as the supply pipelines have actually been eliminated, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing substance.
Prior to moving on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines remain in location in between the faucet and the sink. Safeguard the faucet in place with the maker offered backnut. When the tap is firmly in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet adapters. The previous type must be connected to the faucet ends first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Installing the Tub
Making use of the two wooden boards under its feet, put the bath tub in the called for position. The wooden boards are handy in evenly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to make sure that the bath tub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub until the spirit level reads degree.
To mount taps, fit the bottom of the outermost adaptable tap connector to the appropriate supply pipeline by making a compression join; then do the exact same for the various other tap.
Activate the water as well as examine all joints and also brand-new pipework for leaks as well as tighten them if needed. Fill up the tub and additionally inspect the overflow electrical outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the tub needs to wait until the tub has actually been made use of at least once as this will settle it into its final setting.
Planning for the Installment
To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to see to it that if the faucet includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets system to prevent pressure on the tub.
Fit the adaptable tap adapters to the bottom of the two taps utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to now prepare to be suited its final position.
Tiling Around the Bath tub
In the area where the bath fulfills the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate enough to split a stiff seal, causing the water to permeate the wall in between the bath and also the tiling, causing complications with moisture and also possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are offered in tubes as well as cartridges, as well as can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to securing, to enable the motion experienced when the tub remains in usage. The sealant can split relatively early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are likewise easily available on the marketplace. It is recommended to fit the tiles making use of water-resistant or water-proof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that write-up about Installing A Bathtub from a friend on a different site. Those who appreciated our post kindly make sure you remember to pass it around. Thank you for your time invested reading it.
Quality solution? Call. Report this page